How To Install A Shower Head?

It is actually very easy to install a shower head on your own. You can install your shower head in minutes using the fundamental instruments. Below you will be assisted on how to do it.

Replacing a showerhead enables individuals to enhance their bathroom aesthetics or just fix their leaky issues with the showerhead. You can alter your shower head in just a couple of minutes by using a few instruments and following a few easy steps.

You can readily modify a shower head and arm in less than seven minutes with the instructions below. Using trial and error when dealing with bathroom fixtures is not suggested. This work is for adults or teenagers with high performance.

Gather the tools

You will need to gather all the required tools for the task. These tools include a towel or tarp, an adjustable wrench, a couple of slip-joint pliers, and a fresh shower head. Having Teflon tape could be beneficial. Also CLR solution for cleaning old towels or rags.

1st Step

Clean the shower arm’s threads. Some residual thread binding tape or mineral deposits on the arm can be washed with mild soap and water and/or an ancient toothbrush. We discovered a paper clip can be helpful to remove ancient thread tape from PTFE.

Transfer the readings collected from the shower to identify where you want to open the wall. Locate the studs in the wall with a stud finder to make sure you are where you need to be.

Cut a horizontal line between the wall studs, just above the valve, into the drywall using a keyhole saw. Use them as a guide once you hit the studs and slice the drywall down to the ground. Be cautious and maintain one piece of the drywall. When you need to close the wall back up, you can use it as a patch.

Once you have opened the closet wall behind the shower, it is time to drill the holes in the tile and stub out for the reduced plumbing links you’ll need.

2nd Step

Use the channel lock pliers or monkey wrench to remove the old showerhead. Make sure to turn the pinions in the opposite direction to loosen the ancient shower head.

Remove the arm of the shower by turning it in the diagonal direction by side. Check the quality of the shower arm’s Teflon tape. If the threading of the shower arm is not uniform, make sure that you remember to apply tape to the fresh arm.

Remove the screws from the shower valve trim plate. To remove the handle and plate, remove the hex screw on the handle. Remove the shower valve by using a pipe cutter to cut the 1/2 “copper tubes.

3rd Step

Once the region is smooth, thin-set butter on the back of the tile and press it onto the wall. To align everything, set the spacers around the corners of the tile. Apply the grout once the thin-set has been set and wipe off the surplus.

You need to be sure to use a nice quality grout sealer once your grout cures for at least a week. This is particularly crucial when you do a shower enclosure.

4th Step

Locate the shower wall center. Use a level in the center of the wall to strike a vertical line. Place the shower unit on a shim to lift it off the shower ground slightly, then slide it against the wall and use it as a template to mark the holes for the bolts and water lines.

5th Step

Preassemble the tubes through the wall to place them in. It is just soldered to the tubes by masculine adapters. One for the cold water top pipe, and one for the warm water bottom pipe.

These tubes won’t line up; they need to be offset slightly away from each other so that when it’s in location, the pipes can be readily attached to the shower system.

Cut the cold line from the floor plate about 5-1/2 inches and the hotline from the plate at 3 inches. Cut the water rows in the wall on the row of 3/4-inch size.

For this many showerheads, you will need the complete pipe. Use 90-degree elbows to turn the lines back to the shower system supply lines.

6th Step

Start reinstalling the fresh shower arm by walking hand in a clockwise direction until it’s tight, then put painter’s tape around the arm and tighten the arm with the channel lock or monkey wrench.

The painter’s tape around the shower arm stops scratches or marks on the fresh shower arm from being made by the pliers or wrench. There are two distinct methods of applying the head of the shower.

Solder the tubes of copper in location. Sand the fittings with plumbing sandpaper and copper line. Apply soldering flux and attach the fitting to the pipe. The tubes sweat. Heat the copper pipe with a propane torch until it is sufficiently hot for the solder to liquefy to fill all the gaps between the fitting and the pipe.

If you discover a leak, remove the head of the shower, re-tape the shower arm threads, and re-install the head of the shower. Repeat this method until there are no more leaks.

Final Verdict

Installing a fresh showerhead is a cheap and easy project. Installing a showerhead could involve replacing the shower arm as well, maintaining a coherent finish between the fixtures, and ensuring an accurate fit.

Installation of the showerhead needs the threads to be sealed between the shower arm and the nut. Today’s showerheads include a rubber washer to seal the link between the showerhead and the shower arm inserted inside the nut. This eliminates the use of thread tape that can be unsightly.

Leave a Comment